• Config File

    From IB JOE@1:275/312 to ALL on Mon Feb 10 17:26:36 2003
    Does anyone have a config file that is plain jane just to get bink up and running...

    I use to have one a while back... and don't have a clue how to make it work with out that file..

    Thanx

    Joe

    ... Platinum Xpress & Wildcat!..... Nice!!!!
    --- Platinum Xpress/Win/WINServer v3.0pr5
    * Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)
  • From Gord Hannah@1:17/23.1 to IB JOE on Tue Feb 11 08:19:29 2003
    Replying to a message from IB JOE 1:275/312 to ALL,

    About Config File, On Mon Feb 10 2003

    Does anyone have a config file that is plain jane just to get bink
    up and running...

    A little fancier than plain jane but will get you up and running, I used this for years with a USR Sportster 28.8.

    ; BINKLEY CONTROL FILE
    ;
    Serial 1234
    System Your BBS Name Here
    Sysop Your Name Here
    Address Your Node Number Here
    MyLocation Your Location as it appears in the Nodelist
    MyPhone +1-Finish your Phone Number
    MyListFlags Your Nodelist Flags Here
    ExtBaudRates
    MyMaxBaud 57600
    LockBaud
    PickUpAll
    Banner Welcome to Your BBS
    EnterBBS Press Esc to enter the system or wait a few seconds. BBSNote Thank you, now loading Maximus ...
    DoingMail Sorry; we are currently running a required 2:00-3:00 A.M. mail-only
    event. Shell 1 c:\timed\timed.com
    Shell 2 Bonk
    Shell 3 MFM -ac:\BBS
    Shell 4 UEDIT
    Shell 5 IN.bat
    Shell 6 Out.bat
    Shell 7 Qedit c:\bbs\question.txt
    Shell 8 LIST \bbs\INFO.log
    Shell 9 DEL c:\mail\outbound\*.$$?
    ; CHANGE THE FOLLOWING TO SUIT YOUR NEEDS

    StatusLog c:\BBS\Binkley.log
    Downloads e:\Private\
    CaptureFile c:\BBS\Binkterm.cap
    NetMail i:\Echo\
    NetFile c:\Mail\Inbound\
    Hold c:\Mail\Outbound\
    Version7
    LogLevel 5
    Gong
    ;
    ; Not all systems can handle the stresses of the Janusbaud bi-directional ;
    protocol. If you experience problems, comment out the line below. ;
    JanusBaud 57600
    ;
    Unattended
    Polltries 150
    Nodelist c:\Nodelist\
    MaxReq 10
    MaxBytes 2900000
    About c:\BBS\Error.txt
    Okfile c:\BBS\OKfile.lst
    Avail e:\New\ALLMARSH.zip
    ReqOnUs
    Timeout 20
    BBS Batch
    ScreenBlank call
    Colors 112 14 10 11 7 12 112 3
    Boxtype 2
    CursorCol 1
    CursorRow 25
    ;
    ; Binkley 2.50 specific
    Serial 12345
    StartBlkLen 512
    BlankWait 60
    MaxTime 60
    RingTries 3
    ;
    ; Binkley 2.55 specific
    FileSec 3
    MaxAreas c:\bbs\area.dat
    ;
    ; Binkley 2.59 specific
    ;ModemRetry <modem response>
    ;AltNumber <primary number> <alternate number>
    ;==========================[ MODEM SETUP SECTION ]============================ Port 2
    Baud 57600
    Carrier 80
    Init v~^~ATH0|`AT&F1|~ATM0&K1&S1S2=127S7=90S9=30S10=20S11=50|`ATS15=8S28=20|``AT+FCLASS=0|` Prefix ~AT+FCLASS=0DT
    Suffix `
    Answer ```AT+FCLASS=2\.0|`AT+FBO=1;+FAA=1;+FNR=1,1,1;+FLI="+1-250-786-7921";A|

    ;In the above when receiving with Binkley: +FBO=1
    ;In the above when receiving with BGFax: +FBO=0
    ;
    PreDial `
    PreInit |v``^``|
    DTRHigh
    ;
    ; Add the following responses to Binkley.cfg in the same order! Also ; be sure
    to physically creade the sub-directory in FaxInDir ;
    ModemIgnore +FDM
    ModemIgnore RINGING
    ModemIgnore RING RESPONSE
    ModemRinging RING
    ModemConnect CONNECT
    ModemIgnore RRING
    ModemFailure BUSY
    ModemFailure VOICE
    ModemFailure ERROR
    ModemFailure OK
    ModemFailure NO CARRIER
    ModemIncoming NO DIAL TONE
    ModemIgnore DIALING
    ModemFailure NO ANSWER
    ModemIgnore DIAL TONE
    ModemFax +FCO
    FaxInDir C:\BGFAX\IN
    ;
    ; AfterCall 34 ATI6I11|ATZ| ; ) Just a bunch of samples of the ; AfterCall 18 ATI6| ; ) AfterCall function to record modem ; AfterCall 14 ATI11| ; ) stats in Binkley.log


    I am also assuming that you are using some flavour of DOS. Some modifications will be needed for OS/2.

    Hope this helps. Keep us posted.

    We are a fine board trying to make it better.
    http://www.pris.bc.ca/ghannah
    ghannah@pris.bc.ca
    Cheers! Gord
    -=Team OS/2=-
    --- Timed/2 2.30+
    * Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)
  • From IB JOE@1:275/312 to GORD HANNAH on Tue Feb 11 16:17:56 2003
    No, that was plain enough....

    I have a few questions though...

    I want to use this to call only a few boards... Maybe just a point address.
    Is there a simple way to configure just a few system to call out on??

    I have a copy of XLaxNode ... what is the command line to get that to compile
    a nodelist??

    Thanx

    Joe





    On Feb 11, 2003 08:19am, GORD HANNAH wrote to IB JOE:

    Replying to a message from IB JOE 1:275/312 to ALL,

    About Config File, On Mon Feb 10 2003

    Does anyone have a config file that is plain jane just to get bink
    up and running...

    A little fancier than plain jane but will get you up and running, I
    used this for years with a USR Sportster 28.8.

    ; BINKLEY CONTROL FILE
    ;
    Serial 1234
    System Your BBS Name Here
    Sysop Your Name Here
    Address Your Node Number Here
    MyLocation Your Location as it appears in the Nodelist
    MyPhone +1-Finish your Phone Number
    MyListFlags Your Nodelist Flags Here
    ExtBaudRates
    MyMaxBaud 57600
    LockBaud
    PickUpAll
    Banner Welcome to Your BBS
    EnterBBS Press Esc to enter the system or wait a few seconds. BBSNote Thank you, now loading Maximus ...
    DoingMail Sorry; we are currently running a required 2:00-3:00 A.M. mail-only event. Shell 1 c:\timed\timed.com
    Shell 2 Bonk
    Shell 3 MFM -ac:\BBS
    Shell 4 UEDIT
    Shell 5 IN.bat
    Shell 6 Out.bat
    Shell 7 Qedit c:\bbs\question.txt
    Shell 8 LIST \bbs\INFO.log
    Shell 9 DEL c:\mail\outbound\*.$$?
    ; CHANGE THE FOLLOWING TO SUIT YOUR NEEDS

    StatusLog c:\BBS\Binkley.log
    Downloads e:\Private\
    CaptureFile c:\BBS\Binkterm.cap
    NetMail i:\Echo\
    NetFile c:\Mail\Inbound\
    Hold c:\Mail\Outbound\
    Version7
    LogLevel 5
    Gong
    ;
    ; Not all systems can handle the stresses of the Janusbaud bi-directional ; protocol. If you experience problems, comment out the line below. ; JanusBaud 57600
    ;
    Unattended
    Polltries 150
    Nodelist c:\Nodelist\
    MaxReq 10
    MaxBytes 2900000
    About c:\BBS\Error.txt
    Okfile c:\BBS\OKfile.lst
    Avail e:\New\ALLMARSH.zip
    ReqOnUs
    Timeout 20
    BBS Batch
    ScreenBlank call
    Colors 112 14 10 11 7 12 112 3
    Boxtype 2
    CursorCol 1
    CursorRow 25
    ;
    ; Binkley 2.50 specific
    Serial 12345
    StartBlkLen 512
    BlankWait 60
    MaxTime 60
    RingTries 3
    ;
    ; Binkley 2.55 specific
    FileSec 3
    MaxAreas c:\bbs\area.dat
    ;
    ; Binkley 2.59 specific
    ;ModemRetry <modem response>
    ;AltNumber <primary number> <alternate number> ;==========================[ MODEM SETUP SECTION ]============================ Port 2
    Baud 57600
    Carrier 80
    Init v~^~ATH0|`AT&F1|~ATM0&K1&S1S2=127S7=90S9=30S10=20S11=50|`ATS15=8S28=20|` `AT+FCL ASS=0|` Prefix ~AT+FCLASS=0DT
    Suffix `
    Answer ```AT+FCLASS=2\.0|`AT+FBO=1;+FAA=1;+FNR=1,1,1;+FLI="+1-250-786-7921";A|

    ;In the above when receiving with Binkley: +FBO=1
    ;In the above when receiving with BGFax: +FBO=0
    ;
    PreDial `
    PreInit |v``^``|
    DTRHigh
    ;
    ; Add the following responses to Binkley.cfg in the same order! Also ;
    be sure to physically creade the sub-directory in FaxInDir ;
    ModemIgnore +FDM
    ModemIgnore RINGING
    ModemIgnore RING RESPONSE
    ModemRinging RING
    ModemConnect CONNECT
    ModemIgnore RRING
    ModemFailure BUSY
    ModemFailure VOICE
    ModemFailure ERROR
    ModemFailure OK
    ModemFailure NO CARRIER
    ModemIncoming NO DIAL TONE
    ModemIgnore DIALING
    ModemFailure NO ANSWER
    ModemIgnore DIAL TONE
    ModemFax +FCO
    FaxInDir C:\BGFAX\IN
    ;
    ; AfterCall 34 ATI6I11|ATZ| ; ) Just a bunch of samples of the ; AfterCall 18 ATI6| ; ) AfterCall function to record modem ; AfterCall 14 ATI11| ; ) stats in Binkley.log


    I am also assuming that you are using some flavour of DOS. Some modifications will be needed for OS/2.

    Hope this helps. Keep us posted.

    We are a fine board trying to make it better. http://www.pris.bc.ca/ghannah
    ghannah@pris.bc.ca
    Cheers! Gord
    -=Team OS/2=-
    --- Timed/2 2.30+
    * Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)

    ... Joe's Computer & BBS -=telnet.joesbbs.com=-
    --- Platinum Xpress/Win/WINServer v3.0pr5
    * Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)
  • From Gord Hannah@1:17/23.1 to IB JOE on Tue Feb 11 21:57:45 2003
    Replying to a message from IB JOE 1:275/312 to GORD HANNAH,

    About RE: Config File, On Tue Feb 11 2003

    I have a few questions though...

    I want to use this to call only a few boards... Maybe just a point
    address. Is there a simple way to configure just a few system to
    call out on??


    If you want Bink setup as a point front end that can be done real easy. Two ways get a copy of PPOINT and it will set it up for you or try this it was setup with PPOINT:

    ;=========================================================================== ;Binkley Configuration File for Binkley v2.60 OS/2 ;=========================================================================== ; Port 2
    Baud 115200
    AnswerBack Gord Hannah
    System Point: Marsh BBS (c)
    Sysop Gord Hannah
    Address 1:17/23.1
    Boss 1:17/23
    BossPhone 784-1945
    BossPwd password
    Nodelist f:\adept\mailer\nodelist\
    Version7
    StatusLog H:\LOGS\BINKLEY.LOG
    Downloads H:\MAIL\INBOUND\
    NetMail H:\MAIL\INBOUND\
    NetFile H:\MAIL\INBOUND\
    Hold H:\MAIL\OUTBOUND\
    Prefix ATDT,
    ;
    ;========== Entries above this line should not be changed =======<PART 1>=== ; ;========== Entries below are taken from Binkley.add ============<PART 2>=== ; ;LockBaud 115200
    AutoBaud
    CaptureFile Stuff.CAP
    Carrier 80
    SLOWMODEM
    NOCOLLIDE
    PreInit |v``^``
    Init ^,,,|ATQ0E0H0V1&C1S0=0S2=43X4|,,,
    Suffix ,
    Answer ATA|
    Busy v,^,,ATH0|v
    LogLevel 3
    Gong
    ;Topview
    Janusbaud 115200
    MaxReq 6
    Unattended
    BoxType 1
    Timeout 20
    Colors 112 14 10 11 7 12 112 3
    ScreenBlank
    BBS Exit
    SERIAL 100
    ;
    ;===========================================================================

    I have a copy of XLaxNode ... what is the command line to get that
    to compile a nodelist??

    I don't use Xlax I use Qnode, so the best thing to do is pick up the archive and RTFM.

    Hope this helps. Keep us posted.

    We are a fine board trying to make it better.
    http://www.pris.bc.ca/ghannah
    ghannah@pris.bc.ca
    Cheers! Gord
    -=Team OS/2=-
    --- Timed/2 2.30+
    * Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)
  • From IB JOE@1:275/312 to GORD HANNAH on Wed Feb 12 17:59:34 2003
    Something is amuck!!!

    I want to use com/ip to run Bink over a telnet session, FrontDoor seems to
    like com/ip alright ... bink on the other hand wants to look at my real modem and not the fake com/ip one.

    I have set bink set to port 2, the fake telnet modem, and when bink loads it wants to use com 1...

    BTW, do I need a fossil driver?? Seems to load fine with or without a fossil driver.

    Joe

    ... Joe's Computer & BBS -=telnet.joesbbs.com=-
    --- Platinum Xpress/Win/WINServer v3.0pr5
    * Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)
  • From IB JOE@1:275/312 to GORD HANNAH on Wed Feb 12 18:04:54 2003
    HAHAHA I found the problem!!!!
    I quoted your message to me ... see the word serial?? I thought that meant serial port.... should mention port number in stead!!!!

    Thanx
    Joe
    On Feb 11, 2003 08:19am, GORD HANNAH wrote to IB JOE:

    ; BINKLEY CONTROL FILE
    ;
    Serial 1234
    System Your BBS Name Here
    Sysop Your Name Here

    ... Joe's Computer & BBS -=telnet.joesbbs.com=-
    --- Platinum Xpress/Win/WINServer v3.0pr5
    * Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)
  • From Gord Hannah@1:17/23.1 to IB JOE on Wed Feb 12 21:59:56 2003
    Replying to a message from IB JOE 1:275/312 to GORD HANNAH,

    About RE: Config File, On Wed Feb 12 2003

    I want to use com/ip to run Bink over a telnet session, FrontDoor
    seems to like com/ip alright ... bink on the other hand wants to
    look at my real modem and not the fake com/ip one.

    BTW, do I need a fossil driver?? Seems to load fine with or without
    a fossil driver.

    If in DOS yes I used BNU for years with no problems, In OS/2 you will need SIO,
    and you could use vmodem from that package. If windows sorry can't help some one else will need to address that.

    I don't do windows.

    Hope this helps. Keep us posted.

    We are a fine board trying to make it better.
    http://www.pris.bc.ca/ghannah
    ghannah@pris.bc.ca
    Cheers! Gord
    -=Team OS/2=-
    --- Timed/2 2.30+
    * Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)